The UTC-0965 Steel and UTC-0970 Polyurethane Small Curing Tanks are designed for curing concrete cubes and cylinders. The temperature can be adjusted to the required value and can be kept constant by an electric resistance incorporating a thermo regulator which maintains the set temperature between ambient to 40 ºC with ± 2 ºC accuracy. Running temperature for UTC-0955 Circulating Pump is max. 30 The UTC-0965 is manufactured from powder coated sheet steel. Appropriate curing tank heater and circulating pump should be ordered separately.
The UTC-0950 steel, UTC-0960 and UTC-0962 Plastic Curing Tanks are designed for curing concrete cubes and cylinders. The temperature can be adjusted and can be kept constant by an electric resistance incorporating a digital thermo regulator which maintains the set temperature between ambient to 40 ºC with ± 2 ºC accuracy. The UTC-0950 is manufactured from powder coated sheet steel. Set of removable upper racks (6 pieces) for UTC-0950 to hold concrete cubes are available on request. UTC-0960 and UTC-0962 plastic tanks are reinforced with a metal carcass. Running temperature for UTC-0955 Circulating Pump is max. 30 Appropriate curing tank heater, circulating pump and UTC-0952 for UTC-0950 (in case of need ) should be ordered separately.
The UTC-0650 and UTC-0651 Air Entrainment Meters are used for determining the air content of fresh concrete.They consist of a flanged 7 or 8 liter capacity cylindrical vessel and cover assembly incorporating a pressure gauge, air pump and valves.They have a quick action clamping system. Direct pressure gauge reading to the nearest 0.1% up to 6% air, 0.2% from 6 to 8% air and % 0.5 from 8 to 15%air. It is not affected by changes in barometric pressure. Calibration vessels and compacting bar with square section should be ordered seperately.
Used for the determination of the depth of penetration of water to hardened concrete specimens under pressure. 3 or 6 specimen capacity models and with and without quantitative measurement equipment of water penetratoion models are available. The system can test 150 mm and 200 mm cube specimens, Ø100x200 and Ø150x300 mm cylinder specimens. Up to 10 bar of working pressure is generated on the sample with compressed air applied to the integral water tank and controlled by a pressure regulator with a pressure gauge with 0,2 bar graduations. The test sets with the quantitative measurement equipment of water penetratoion the penetration of water is measured through the burettes. The system comprises impermeability gaskets for every cell. The measurement apparatus is supplied as standard. The apparatus has to be fitted with a suitable air compressor. The Air Compressor should be ordered separately. Compressed air controlled by a pressure regulator with a pressure gauge with 0,2 bar graduations.
The machines allow inexperienced operators to perform the test. Once the machine has been switched on and the specimen is positioned and centered by the help of concentric centering line/s of lower bearing block the only required operations are; Setting test parameters, including pace rate (only required when the specimen type is changed). Pressing the START button on the control unit. The machine automatically starts the rapid approach, when the specimen touches the upper platen the rapid approach is ended and starts loading at the pace rate that selected by user and stops once the specimen fails. Automatically saves the test parameters and test results. The Machines consist of a welded steel frame ( see table), hydraulic power pack with U-Touch PRO Control Unit. Main Features Safety Features U-Touch PRO Control Unit UTC-4930.FPR is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. All the operations of U-Touch PRO are controlled from the front panel touch screen display. U-Touch PRO Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics UTEST Software for Automatic Compression / Flexure Testing Machines UTEST software USOFT-4830.FPR provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. The advantages of performing tests on computer with using UTEST Software, such as reporting, graphical output, etc. can be seen in detail at the pages of UTEST Software for Automatic Compression / Flexure Testing Machines. Optional Additional Frame For compression and especially flexural testing, additionally second testing frame should be ordered separately. In this case, the machines provide load control of two seperate testing frames with closed-loop P.I.D control with automatic test procedure by using selecting test channel And additional selector valve.
UTC-6729.FPR, UTC-6739.FPR, UTC-6749.FPR and UTC-6759.FPR models Automatic Compressıon Testıng Machines are manufactured for compression testing of masonary units, cubes and cylinders acc. to EN standards .These machines also meet the requirements of CE norms with respect to the health and safety of the operator. The machines allow inexperienced operators to perform the test. Once the machine has been switched on and the specimen is positioned and centered by the help of fixtures or/and concentric centering lines of lower loading platen, the only required operations are; Setting test parameters, including pace rate (only required when the specimen type is changed). The Machines consist of a welded steel frame (see table) and UTC-4830FPR automatic hydraulic power pack with U-Touch PRO Control Unit. UTC-4684 and UTC-4886 Pedestals that are made of steel to facilitate the user’s placement of specimens in the machines for compression test should be ordered separately. Main Features Pace Rate control between 1 kN to 25 kN Accuracy Class 1 acc. to EN 12390-4 starting from with the 5% of the machine capacity (Special calibration option Class 1 starting from 1% of the full range with UTC-0210) Supplied with factory calibration certificate for force transfer stability and the self-alignment of the upper loading platen conforming to EN 12390-4 Tests automatically with closed loop control The tests can be performed by controlling the machine either on U-Touch PRO control unit (UTC-4930.FPR) or on a computer with using free UTEST Software (USOFT-4830.FPR) which is provided free of charge with the machines. Load measurment with a pressure transducer Hydraulic pump with dual stage for rapid approach Welded steel walled frame with a single acting piston Piston return at the end of test automatically U-Touch PRO Control Unit U-Touch PRO Control Unit UTC-4930.FPR is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. All the operations of U-Touch PRO are controlled from the front panel touch screen display. U-Touch PRO Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics PLEASE see the pages of “U-Touch PRO Control Unit for Automatic Compression/Flexure Testing Machines” for details of the properties. UTEST Software for Automatic Compression / Flexure Testing Machines UTEST software USOFT-4830.FPR provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. The advantages of performing tests on computer with using UTEST Software, such as reporting, graphical output, etc. can be seen in detail at the pages of UTEST Software for Automatic Compression / Flexure Testing Machines. Optional Additional Frame For compression and especially flexural testing, additionally second testing frame should be ordered separately. In this case, the machines provide load control of two seperate testing frames with closed-loop P.I.D control with automatic test procedure by using selecting test channel And additional selector valve. Safety Features Maximum pressure valves to avoid machine overloading Limit switch for piston stroke Emergency stop button Removable transparent front and rear safety doors Software controlled maximum load value • • • • Appropriate distance piece/s for the cylinder and cube specimens with the height of lower than 150 mm should be ordered separately for UTC-6729.FPR and UTC-6739.FPR
UTC-5729.FPR and UTC-5739.FPR models Automatic Compressıon Testıng Machines are manufactured for compression testing of masonary units, cubes and cylinders acc. to EN standards .These machines also meet the requirements of CE norms with respect to the health and safety of the operator. The machines allow inexperienced operators to perform the test. Once the machine has been switched on and the specimen is positioned and centered by the help of fixtures or/and concentric centering lines of lower loading platen, the only required operations are; Setting test parameters, including pace rate (only required when the specimen type is changed). The Machines consist of a welded steel frame (see table) and UTC-4830FPR automatic hydraulic power pack with U-Touch PRO Control Unit. Main Features Pace Rate control between 1 kN to 25 kN Accuracy Class 1 acc. to EN 12390-4 starting from with the 5% of the machine capacity (Special calibration option Class 1 starting from 1% of the full range with UTC-0210) Supplied with factory calibration certificate for force transfer stability and the self-alignment of the upper loading platen conforming to EN 12390-4 Tests automatically with closed loop control The tests can be performed by controlling the machine either on U-Touch PRO control unit (UTC-4930.FPR) or on a computer with using free UTEST Software (USOFT-4830.FPR) which is provided free of charge with the machines. Load measurment with a pressure transducer Hydraulic pump with dual stage for rapid approach Welded steel walled frame with a single acting piston Piston return at the end of test automatically U-Touch PRO Control Unit U-Touch PRO Control Unit UTC-4930.FPR is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. All the operations of U-Touch PRO are controlled from the front panel touch screen display. U-Touch PRO Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics UTEST Software for Automatic Compression / Flexure Testing Machines UTEST software USOFT-4830.FPR provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. The advantages of performing tests on computer with using UTEST Software, such as reporting, graphical output, etc. can be seen in detail at the pages of UTEST Software for Automatic Compression / Flexure Testing Machines. Optional Additional Frame For compression and especially flexural testing, additionally second testing frame should be ordered separately. In this case, the machines provide load control of two seperate testing frames with closed-loop P.I.D control with automatic test procedure by using selecting test channel And additional selector valve. Safety Features Maximum pressure valves to avoid machine overloading Limit switch for piston stroke Emergency stop button Removable transparent front and rear safety doors Software controlled maximum load value EN 12390-4 and EN 772-1 COMPRESSION TESTING (d*) depth (**) Limited by capacity of the frame The machines for masonary units, cubes and cylindrs are supplied complete with; • • • • Removable transparent front and rear safety doors Appropriate Distance piece/s for the cylinder and cube specimens with the height of lower than 150 mm should be ordered separately.
UTC-6727.FPR, UTC-6737.FPR UTC-6747.FPR and UTC-6757.FPR models Automatic Four Column Compressıon Testıng Machines are manufactured for compression testing of cubes and cylinders acc. to EN. These machines also meet the requirements of CE norms with respect to the health and safety of the operator. The machines allow inexperienced operators to perform the test. Once the machine has been switched on and the specimen is positioned and centered by the help of fixtures or/and concentric centering lines of lower loading platen, the only required operations are; Setting test parameters, including pace rate (only required when the specimen type is changed). The Machines consist of a welded steel frame (see table) and UTC-4830FPR automatic hydraulic power pack with U-Touch PRO Control Unit. Main Features Pace Rate control between 1 kN to 25 kN Accuracy Class 1 acc. to EN 12390-4 starting from with the 5% of the machine capacity (Special calibration option Class 1 starting from 1% of the full range with UTC-0210) Supplied with factory calibration certificate for force transfer stability and the self-alignment of the upper loading platen conforming to EN 12390-4 Tests automatically with closed loop control Load measurment with a pressure transducer U-Touch PRO Control Unit for Automatic Compression / Flexure Testing Machines U-Touch PRO Control Unit UTC-4930.FPR is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. All the operations of U-Touch PRO are controlled from the front panel touch screen display. U-Touch PRO Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics UTEST Software for Automatic Compression / Flexure Testing Machines UTEST software USOFT-4830.FPR provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines The advantages of performing tests on computer with using UTEST Software, such as reporting, graphical output, etc. can be seen in detail at the pages of UTEST Software for Automatic Compression / Flexure Testing Machines. Optional Additional Frame For compression and especially flexural testing, additionally second testing frame should be ordered separately. In this case, the machines provide load control of two seperate testing frames with closed-loop P.I.D control with automatic test procedure by using selecting test channel And additional selector valve. Safety Features Maximum pressure valves to avoid machine overloading Limit switch for piston stroke Emergency stop button Removable transparent front and rear safety doors Software controlled maximum load value
The Epoxy Coated Dowel Bar is a strategic connection element designed to transfer vertical and horizontal loads between concrete blocks, preventing relative motion and deformations. The use of this innovative solution allows the weight of moving tools to be distributed among multiple concrete blocks, eliminating potential deformations and ensuring stability.
Epoxy-Coated Reinforcing Bar - Rebar for strategic infrastructures & superstructures. When miscellaneous chemicals used in strategic and qualified infra and superstructures, roads, bridges, viaducts and industrial plants and various environments and processes and natural factors such as rainwater, moisture etc. penetrate into steel fittings inside the foundation concretes, concrete platforms, concrete columns and beams which function as load-bearing components, corrosion formation occurs in these steel fittings.
Tie Bars are epoxy-coated steel equipment used to strengthen reinforced concrete constructions. Epoxy Coated Tiebars are used along with Epoxy Coated Dowelbars. Epoxy Coated Tiebars are placed in parallel with pavement surface in specific intervals to be determined for the reinforced concrete areas. When the concrete is poured, the reinforced concrete construction turns into more solid, more flexible and more endurable construction thanks to Epoxy Coated Dowelbars and Epoxy Coated Tiebars inside.
Pre-applied waterproofing membrane conforming to the requirements of BS EN 13967:2012 and BS 8102:2009. Proofex Engage mechanically bonds to poured concrete, remaining in place if settlement of substrate occurs
