The UTC-0965 Steel and UTC-0970 Polyurethane Small Curing Tanks are designed for curing concrete cubes and cylinders. The temperature can be adjusted to the required value and can be kept constant by an electric resistance incorporating a thermo regulator which maintains the set temperature between ambient to 40 ºC with ± 2 ºC accuracy. Running temperature for UTC-0955 Circulating Pump is max. 30 The UTC-0965 is manufactured from powder coated sheet steel. Appropriate curing tank heater and circulating pump should be ordered separately.
The UTEST fixed amplitude vibrating tables are compact units providing controlled vibro-compaction forcube or cylinder moulds. Vibrating tables consist of vibrating motor, command unit and clamping assembly. For laboratory use the table is availablein two alternative model. The small table accepts 2, large table accepts 6 cube or cylinder moulds by using clamping assembly. UTC-0900 and UTC-0910 tables can also be used for beam moulds. For on site applications, portable UTC-0920 Vibrating Table is designed for preparing the cube or cylinder specimens by vibration. 1 or 2 pcs. cube or cylinder mould can be clamped on the table depending on outer size of the mould to be used. UTC-0920 Vibration Tables are supplied complete with a converter (DC 12 to 220V).
Used for the determination of the depth of penetration of water to hardened concrete specimens under pressure. 3 or 6 specimen capacity models and with and without quantitative measurement equipment of water penetratoion models are available. The system can test 150 mm and 200 mm cube specimens, Ø100x200 and Ø150x300 mm cylinder specimens. Up to 10 bar of working pressure is generated on the sample with compressed air applied to the integral water tank and controlled by a pressure regulator with a pressure gauge with 0,2 bar graduations. The test sets with the quantitative measurement equipment of water penetratoion the penetration of water is measured through the burettes. The system comprises impermeability gaskets for every cell. The measurement apparatus is supplied as standard. The apparatus has to be fitted with a suitable air compressor. The Air Compressor should be ordered separately. Compressed air controlled by a pressure regulator with a pressure gauge with 0,2 bar graduations.
The UTCM-0930 Vibrating Machine is used for the preparation and compaction of 70.7 mm mortar cube specimens. The mould table is mounted on four springs attached to an eccentric shaft which allows each sample to be vibrated at 12000 cycles per minute. There is a timer on it to preset time and it stops automatically in every 120 seconds. 70.7 mm cube mould (UTCM-0926) should be ordered separately.
UTCM-1100 Curing Cabinet, 1000 Liters, for cement based mortar specimens, 20.0 ± 1.0°C temperature and over 90% Rh humidity. The humidity and temperature can be controlled and monitored by a digital unit. Stainless steel interior. 220-240V, 50-60Hz, 1ph. The humidity and temperature can be controlled and monitored on the digital control unit. UTCM-1100 Curing Cabinet is also supplied complete with six displaceable shelves.
All moulds have been manufactured from steel except UTCM-0898 molded using engineered plastic and all internal surfaces are machined. Minimum surface hardness of UTCM- 0892.4 is HV400 which is recommended by the EN standard. All moulds surfaces are protected with anti-corrosion oil. The webs of UTCM- 0892.4 and UTCM-0899A are matchmarked. Minimum surface hardness of UTCM-0892.2 is HV200.
Jolting Table is used for compacting of cement specimens in 40x40x160 mm mould and consists of mould table seated on a rotating cam driven at 60 r.p.m. The falling height is 15 mm conforming to EN 196-1. The machine is equipped with a counter which provides automatic shut off at end of preset drop numbers. Weight and dimensions of the jolting table fully comply with the requirements of EN 196-1 standard. When used with UTCM-0892 Three Gang Mould and UTCM-0893 Feed Hopper, the total weight of the moving part is 20 kg ± 0.5 kg. Without UTCM-0892 and UTCM-0893 the weight of the moving parts is 6.85 kg. Rapid mould lock and release system allows easy and quick operation. The supporting frame of the machine has been designed to ensure precise dimensions, table flatness, correct centering of the three gang mould on the table. The motor and gearbox assembly is enclosed in a protective housing, which promotes user safety (the moving parts are inaccessible) and long life for the gearbox. The standard model can be supplied with a safety/noise reduction cabinet. The cabinet is lined internally with soundproofing material to reduce sound level conforming to CE directives. UTCM-0893 Feed Hopper is used for filling UTCM-0892 Three Gang Moulds placed on the Jolting Table. UTCM-0892 Three Gang Mould, UTCM-0893 Feed Hopper, UTCM-0894 Short and Long Spreaders and Straightedge should be ordered separately.
There are two models of the Cement Flow Table according to ASTM and EN standard. Both are used for determining the consistency of mortar, lime and cement specimens. Also manual and motorized models are available. The hand operated model is fitted with a hand wheel. The motor operated model is driven by a motor speed reducer through a mechanical coupling at the rate of 1 revolution per second. The number of drops is preset on a counter and the machine stops automatically at the end of the cycle. EN model, the table is manufactured from stainless steel and has a 300 mm diameter table. The conical mould is made of stainless steel and has dimensions of 100 mm base dia. x 70 mm top dia. x 60 mm height. ASTM model; the table is manufactured from bronze and has 254 mm diameter. The conical mould is made of brass has dimensions of 100 mm base dia. X 70 mm top dia. X 50 mm height. Both models are supplied complete with stainless steel flow mould and tamper. EN model also has a stainless steel hopper.
The Skid Resistance and Friction Testers are used for the measurement of surface friction properties. The apparatus is suitable for both site and laboratory applications and for Polished Stone Value tests using curved specimens from accelerated polishing tests with the Acelereted Polishing Machine (UTA-0810). UTA-0830E can also be used for testing Paving Stones (EN 1341, EN 1342) and Paving Blocks (EN 1338). The apparatus consist of an adjustable pendulum arm, and a spring loaded rubber slider (see accessories) mounted on the end of the arm. Rubber sliders should be ordered separately.
EN 12504-2, 13791; ASTM C 805; D 5873; BS 1881:202; NF P18-417; DIN 1048; UNI 9189 The quality of concrete is mainly judged by its compressive strength directly affecting the load-bearing capacity and durability of concrete structures. UTC-3028 Concrete Test Hammer (Schmidt Hammer N Type UTEST) is used to measure the compressive strength characteristics of hardened concrete non-destructively, control uniform concrete quality and detect weak spots in the concrete. The test object should have a minimum thickness of 100 mm (3.9 in). The impact area of UTC-3040 Calibration Anvil used for the calibration of concrete test hammers is hardened minumum 52HRC.
UTC-5727.FPR and UTC-5737.FPR models Automatic Compressıon Testıng Machines are manufactured for compression testing of cubes and cylinders acc. to EN 12390-4. These machines also meet the requirements of CE norms with respect to the health and safety of the operator. The machines allow inexperienced operators to perform the test. Once the machine has been switched on and the specimen is positioned and centered by the help of fixtures or/and concentric centering lines of lower loading platen, the only required operations are; Setting test parameters, including pace rate (only required when the specimen type is changed). Main Features Pace Rate control between 1 kN to 25 kN Accuracy Class 1 acc. to EN 12390-4 starting from with the 5% of the machine capacity (Special calibration option Class 1 starting from 1% of the full range with UTC-0210) Supplied with factory calibration certificate Tests automatically with closed loop control Load measurment with a pressure transducer Multi-Point calibration function for the channels Real time numeric display of load and load pressure with test graph. Safety Features Maximum pressure valves to avoid machine overloading Limit switch for piston stroke Removable transparent front and rear safety doors Optional Additional Frame For compression and especially flexural testing, additionally second testing frame should be ordered separately. In this case, the machines provide load control of two seperate testing frames with closed-loop P.I.D control with automatic test procedure by using selecting test channel and additional selector valve. U-Touch PRO Control Unit UTC-4930.FPR is designed to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines. All the operations of U-Touch PRO are controlled from the front panel touch screen display. U-Touch PRO Control Unit has easy to use menu options. It displays all menu option listings simultaneously, allowing the operator to access the required option in a seemless manner to activate the option or enter a numeric value to set the test parameters. Digital graphic display is able to draw real-time "Load vs. Time", or "Stress vs. Time" graphics UTEST Software for Automatic Compression / Flexure Testing Machines UTEST software USOFT-4830.FPR provides to perform automatically compression, flexure and splitting tensile strength tests of construction materials such as concrete, cement mortar, masonary units/blocks by controlling the Utest automatic compression / flexure testing machines The advantages of performing tests on computer with using UTEST Software, such as reporting, graphical output, etc. can be seen in detail at the pages of UTEST Software for Automatic Compression / Flexure Testing Machines. EN 12390-4 AUTOMATIC COMPRESSION TESTING MACHINES The machines for cubes and cylinders are supplied complete with; • • Fixture for centering specimens, compatible with Ø300 mm lower loading platen for 100 mm and 150 mm cubes, Ø100 mm and Ø150 mm cylinders (UTC-4622E) • Removable transparent front and rear safety doors
Distance Pieces for Frame Due to the modular design of the frames any sample with suitable size, load and pace rate can be test on both chambers by decreasing the distance between platens. Loading Platens UTCM-4116 Lower and Upper (spherical seated) Loading Platens are manufactured from high quality steel smoothed and finished. The roughness value for the surface texture of machine and auxiliary platens are 3.2 μm.
